Used 8536-460 Brown & Sharpe Universal Sliding Head Horizontal/Vertical Milling Machine,Rangemaster #20 For Sale

Asking Price
Contact Me for Price
Stock:
Only 2 Available on the Marketplace!
Seller:
Member ID 53582 - avatar

David L.

Member since: February 2015

More listings by this seller

Make an Offer Ask the Seller a Question
Name:
8536-460 Brown & Sharpe Universal Sliding Head Horizontal/Vertical Milling Machine,Rangemaster #20
Listing Reference:
582866
Price:
Contact Me for Price
Location:
RI, USA
Age:
Unknown
Description:

8536-460 Technical Specifications: 220V/3PH/50-60HZ S/N: 506-20-32 Table working surface: 10" x 50" Table Swivels: plus or minus 50 degrees Number and width of table t-slots: (3) 11/16" Table travel: 29" x 11" Knee travel: 14" Top ram travel: 24" Spindle taper, horizontal: #50 N.S.T. Spindle taper, universal milling head: #40 N.S.T. Axial feed (hand feed) of universal milling head: 3-1/2" Transverse adjustment of sliding head: 22-7/8" (18) Feeds: 1/2 to 20-1/4 I.P.M. (18) Speeds, horizontal: 40 to 1,530 R.P.M. (18) Speeds, universal milling head: 80 to 3,060 R.P.M. Rapid traverse rate, all directions: 75 I.P.M. Minimum/Maximum distance from centerline of horizontal spindle to top of table: 21/32" / 21-5/8" Distance from centerline of universal milling head spindle to column face: 2-1/16 / 24-15/16" Spindle speeds: 40 - 1535 RPM Number of speeds: 18 Table feeds: 1-1/2 - 20-1/4 IPM (19) Overall dimensions: 64" x 76" x 80" H Approximate Weight: 5,350 Lbs Equipped With: Universal, swivel table Universal (double swivel) milling head with manual micrometer quill travel Sliding head design allowing the spindle and its driving motor to be extended so that its face is up to 15-3/16" away from the machine column face. This permits the spindle nose to be brought out close to the cutter while adequate clearance is given to work or fixtures projecting over the table. Another advantage of the sliding head design is obtained when an end mill is being used in the nose of the horizontal spindle. (1) Arbor support Approximately (10) #50 N.S.T. tool holders Approximately (18) #40 N.S.T. tool holders Manual draw bolt for both horizontal and vertical spindles Movable pendant control Self-contained coolant pump 1 H.P. feed motor 3 H.P. 3/60/220-440 volt spindle drive motor and electrical controls Manual included Click On Images To View Full Size:

Used equipment can sell very quickly. Contact the seller asap to discuss this 8536-460 Brown & Sharpe Universal Sliding Head Horizontal/Vertical Milling Machine,Rangemaster #20.

Make an Offer Ask the Seller a Question
Asking Price
Contact Me for Price
Stock:
Only 2 Available on the Marketplace!
Seller:
Member ID 53582 - avatar

David L.

Member since: February 2015

More listings by this seller

Make an Offer Ask the Seller a Question
Make the Seller an Offer

Make the Seller an Offer

* required field

$ (USD)

Sending an offer to the seller does not constitute a legally binding agreement to purchase the equipment. However, please only make an offer if you are seriously interested.

Your offer will be emailed to the seller immediately. We will email you their reply as soon as we receive it.

Ask the Seller a Question

Ask the Seller a Question

* required field

Your question will be sent to the seller immediately and we will email you as soon as they reply.