Hawker Sidley -

Listing description

Description CUT-TO-LENGTH & SLITTER LINE - WIDTH: 153-1220 MM - THICKNES: 0.25-3.0 MM
Year 1981
Brand HAWKER SIDDELY - B&K DIVISION
Qty. 1 Second-hand cut-to-length / slitter line
Mfc. Hawker Siddely – B & K Division Built
Material Al alloys 1100, 3003 & 5052 Material temper
Yield strength min./max. 3.52 / 26.74 kg/mm² Shear strength
Material thickness 0.25 – 3.0 mm Width min./max.
Coil weight 5,000 kg Coil O/D – I/D

1. Cut-to-length
Length cut min./max. 153 / 10,000 mm Width min./max.
Length tolerance +/- 0.5 mm No. of cuts
Number of width – max. 3 (plus edge trim) Line speed
2. Slitter
No. of cuts 3 mm thick material 8 cuts
2 mm thick material 13 cuts
1 mm thick material 25 cuts
Min. Width – slit 25 mm Line speed
Line tension 1.785 kg Hand of line – C.T.L.
Power supply 220 V, 3 ph., 60 Hz
Air supply 185 PSI Clean dry air - @ 50 CFM
Scope of supply
1. Coil car Model 10CCFM-04-E Floor mounted coil car (entry & exit)
Capacity 5000 kg Max. coilm O/D
Lift speed 1.5 m/min. Lift actuation
Traverse actuation Hydraulic orbit motor, chain & sprocket drive
Traverse speed 7 m/min. Hydr. power source Entry power pack
Hydr. supply Trailing flex hose Controls Manually operated valves
2. Uncoiler Model UMII-13-E Single mandrel
bi-directional operation Capacity 5000 kg Mandrel type
Mandrel expansion range 393 – 483 mm
Means of expansion hydr. operated wedges
Drive – Mandrel hydrostatic hydraulic orbit motor chain & sprocket
Tension brake air operated water cooled disc type brake Wichita 216
Hold-Down Roll 254 mm dia. x 406 mm face width
Hold-Down roll actuation hydraulic cylinder Lateral traverse
Means of traverse hydraulic cylinder Tension capacity
Hydraulic power from line central power unit
3. Combination Slitter – Flattener – Flying shear unit
Model COU-01-30-E 5S-05-10-E & 5S-05-E FAS-02-E & 30DA-37-E
Entry guides free running support rolls Entry pinch roll
Slitter knife dia. 228 mm Intermediate pinch rolls
Number of flattener rolls 7 (3 bottom – 4 top) Flattener roll
Exit lower pinch roll 114 dia. x 1371 mm face Upper exit measuring roll
Blade type (4) cutting edge Upper blade movement
Air supply (by customer) 185 PSI x 50 CFPM Max. cuts
Shear accelerator Patented rack & pinion Shear return
Measuring system Solid state micromatic pre-set counter & circumferential pulse
measuring system
Drive 15.1 kW, 1760 RPM, DC motor & gearbox Slitter arbor dia.
4. Piler bar type manual stacker Model SS-29-E Fixed rear stop
Adjustable side plate Location adjacent to flying shear
Side plaet adjustment 610 mm Length of side plate
Means of adjustment manual
5. Qty. 2 Scrap winders Model SW-02-E
Max. scrap ball size 762 mm O/D x 355 mm I/D x 305 mm wide
Scrap size 20 mm x 3.0 mm max. – 2 strands Drive
Hydraulic power central hydraulic power unit
6. Scrap winder Model SW-02-E
Max. scrap ball size 762 mm O/D x 355 mm I/D x 305 mm wide
Scrap size 20 mm x 3.0 mm max. – 2 strands Drive
Hydraulic power central hydraulic power unit Scrap oscillator
7. Slitter base & pinch rolls & entry guides Model 5S-05-20-E
Free standing unit Individually adjusted guides with one set of pinch rolls
Pinch roll 152 mm dia. x 1320 mm face length
Bottom roll lift pneumatic cylinders Entry guide rolls per side
Guide roll size 3” dia. x 4” length
Entry guide adjustment threaded spindles (2) & detachable hand crank
Bottom pinch roll drive hydr. motor
Coil peeler mounts (2) mounting blocks drilled on base
Entry guide height adjustment slotted holes & Jack screws
8. Recoiler with overarm separator Model 10RG-06-E
Single madrel with overarm separator Capacity 9090 kg max.
Coil O/D 1524 mm max.
Mandrel expansion range 495 – 508 mm through circle at 508 mm dia.
Means of expansion manual Type of mandrel
Gripper orientation overwind only Gripper bar actuiation
Coil push-off (stripped) hydr. operated with spring loaded segment
Overarm separator actuation 254 mm dia. pneumatic cylinder
Recoiler drive 25 HP, AC motor, 1800 RPM Recoiler speed
Holding brake motor mounted Control valves – hydraulic
Vlave location machine mounted
Lubrication gear reducer by splash oil lubrication.
All other points through separate grease fittings.
9. Hydraulic power unit Mfc. Vickers Model
Capacity 320 L Pump size
Working pressure 0.7 kg/mm²

10. Electrical equipment
The electrical equipment include all AC & DC motors & controls. NEMA 1 enlcosure
Isolation transformer Primary
Auto transformer starter for recoiler
11. Air compressor No. 3150-15 Type air cooled – 2 stage – 4 cylinders
Compressor drive 20 HP, AC & “V-belt” Tank
Air delivery 50 CFM @185 PSI
12. Spare parts
13. Slitting tooling
14. Overarm separator tooling

This equipment is located in DE