Heller 1809EXL

Listing description

Model 1809EXL (Air) 1809EXL (Nitrogen)
Electric Supply
Power Input (3 Phase) Standard 480 volts 480 volts
Breaker Size 100 amps @ 480v 100 amps @ 480v
kW 11-13 Continuous* 11-13 Continuous*
Typical Run Current 25-30 amps @ 480v 25-30 amps @ 480v
Optional Power Inputs Available 208/240/380/400/440/415 VAC 208/240/380/400/440/415 VAC
Frequency 50/60 Hz 50/60 Hz
Sequential Zone Turn On S S
Single Phase Operation Not Available Not Available
Dimensions
Overall Length 183″ (465 cm) 183″ (465 cm)
Overall Width 54″ (137 cm) 54″ (137 cm)
Overall Height 63″ (160 cm) 63″ (160 cm)
Typical Net Weight 3500 lbs. (1588 kg) 3500 lbs. (1588 kg)
Typical Shipping Weight (Domestic) 4000 lbs. (1814 kg) 4000 lbs. (1814 kg)
Typical Shipping Weight (Export) 4500 lbs. (2041 kg) 4500 lbs. (2041 kg)
Computer Control
AMD or Intel Based Computer S S
Recipe Storage > 500 > 500
Flat Screen Monitor S S
Windows Operating System Windows XP® Windows XP®
Monitor mount S S
Auto Start Software S S
Data Logging S S
Password Protection S S
LAN Networking O O
Inert Atmosphere
Minimum PPM Oxygen – 10-25 PPM
Nitrogen Cooling – S
Waterless Cooling w/ Flux Separation System – O
Nitrogen On/Off Valve – O
Oxygen Monitoring System – O
Nitrogen Standby System – O
Sample Port in Reflow – S
Typical Nitrogen Consumption – 700 – 900 SCFH **
Additional Features
KIC / ECD Profiling Software S S
Signal Light Tower S S
Powered Hood Lift S S
Five (5)Thermocouple Profiling S S
30” Heater Modules O O
Redundant Alarm Sensors O O
Independent Alarm Scanner O O
KIC Profiler / ECD Profiler O O
Center Board Support O O
Board Drop Sensor O O
Board Counter O O
Bar Code Reader O O
Custom Paint & Decal O O
Battery Backup for Conveyor and PC O O
GEM/SECS Interfacing O O
Custom Engineering and Software Available Available
* Varies depending on Options included with the oven Specifications Continue on Reverse
** Tested at 500 PPM. Varies with PCB size and oven configuration
Heller Reflow Oven Specifications (Continued)
Model 1809EXL (Air) 1809EXL (Nitrogen)
Mesh Belt Conveyor
Height From Floor 35.5″ + 2.0″ (90 cm + 5 cm) 35.5″ + 2.0″ (90 cm + 5 cm)
Maximum PCB Width
*** Requires 30” Heater Modules 22″ (55.8 cm)
26” (66 cm)** 10″ (25 cm) 15″ (38 cm) 18″(46 cm)
22″ (55.8 cm) 26” (66 cm)**
Space Required Between PCB’s 0.0″ (0.0 cm) 0.0″ (0.0 cm)
Conveyor Length On-Load 18″ (46 cm) * 6″ (15 cm) *
Conveyor Length Off-Load 18″ (46 cm) * 6″ (15 cm) *
Heated Tunnel Length 105″ (254 cm) 105″ (254 cm)
Process Clearance Above Mesh Belt 2.3″ (5.8 cm) 2.3″ (5.8 cm)
Mesh Belt Pitch 0.5″ (1.27 cm) 0.5″ (1.27 cm)
Maximum Conveyor Speed 74″/Min (188 cm/min.) 74″/Min (188 cm/min.)
Conveyor Direction Left to Right S S
Conveyor Direction Right to Left O O
Conveyor Speed Control Type Closed Loop Closed Loop
Edge Hold Conveyor System Option
Height from Floor – Standard 37.0″ + 2.0″ (94 cm + 5 cm) 37.0″ + 2.0″ (94 cm + 5 cm)
Height from Floor – Optional 32.6″ +3.9″ / -.4″
(83 cm + 10 cm / -1 cm) 32.6″ +3.9″ / -.4″
(83 cm + 10 cm / -1 cm)
Clearance Above Conveyor Pins 1.15″ (2.9 cm) 1.15″ (2.9 cm)
Clearance Below Conveyor Pins 1.15″ (2.9 cm) 1.15″ (2.9 cm)
Length of PCB Support Pins .187″ (4.75 mm) .187″ (4.75 mm)
3 mm long support pins O O
Minimum/Maximum Board Width
*** Requires 30” Heater Modules 2.0″ – 20″ (5 – 50.8 cm)
24” (61 cm)** 2.0″ – 20″ (5 –50.8 cm)
24” (61 cm)**
Edge Hold Rail Heaters Not Required Not Required
Power Width Adjustment S S
Computer Controlled Width Adjust O O
Auto Lubrication System S S
Forced Convection Zones
Top 9 9
Bottom 9 9
Heater Type Instant response open coil Instant response open coil
Heater Material Nichrome Nichrome
IR Panel Heaters (For Curing) O O
Temperature Control
Accuracy of Temperature Controller + .1°C + .1°C
Cross-Belt Temperature Tolerance + 3.0°C + 3.0°C
Heater Wattage Per Zone 6000 w 6000 w
Temperature Range Standard 25-350°C 25-350°C
High Temperature Up to 400°C O O
High Temperature Up to 450°C O O
Insulation Type Calcium Silicate Calcium Silicate
UV Cure O O
Cooling Systems
Number of Cooling Zones Standard 2 2
Additional Cooling Zones (External) O O
Water Cooling – O
Waterless Cooling – O
Notes: S = Standard, O = Optional. * A 12″ (30 cm) Conveyor extension is an available option Specifications continue on reverse.

This equipment is located in IE