Manufactured 1992 Specifications Features Model No.: WD100HE-Q Capacity: 100 lbs/hr Dewpoint: +10 to -40 degrees F Max. Standard Temp.: up to 400 degrees F Electrics: 460/3/60 Whitlock 300 lb. Ins. Hopper Model DH2 OMI-HE-Q - Door - Sight glass - Dump tube - Take-off box w/Conair Vacuum Loader
Specifications Features Model:: GB-140 Capacity:: 350-475 lbs/hr Compartments:: 4 Motor: Bison 1/15 HP Electrics: 115 volt Controls: Maguire Casters can be added to make unit more portable... P.O.R. Weigh controller has a 17 pin plug
All stainless steel blender with mezzanine. The blender has a 3 piece hinged cover with a bag dump station in the middle. The blender is 35" wide x 87" long (approximately 50 cubic feet). It has a 8" centre discharge with air actuated butterfly valve and air purge seals. The mezzanine is 185" wide (including stairs) x 84" deep. The mezzanine has railing with removable section for putting pallets up. Clearance under the mezzanine is 65.75" high. Comes with control panel and main on / off switch. Powered by a Leeson 25 hp motor with Brook Hansen 45/1 gear box. In good working condition. Last used for blending neutraceuticals.
This dough mixer has 2 speeds with timers and bowl reverse. The stainless steel bowl is 26.75" diameter x 15.5" deep. It has guarding over the bowl with a lock out shut off if lifted while in operation. The machine has 1 set of wheels at the back and leveling feet at the front. The set of wheels need to be replaced because they have peeled apart. In good working condition. Last used in a bakery.
This is an electrically heated jacketed kettle with double motion scrape surface mixer and emulsifier with vacuum capabilities. The kettle is 18" diameter x 20.25" deep (50 litre capacity). The lid has 2 inlets, a spray ball inlet and 2 vacuum ports. There is a viewing port and a light inside that can come on to see inside when mixing. The mixer is double motion and can run 0 - 64 rpm. The homogenizer runs down the centre of the mixer and sits at the bottom of the kettle. It can run 0 - 3600 rpm. It has a 1.5" ball valve outlet that's connected to a hose so it can drain out the back of the unit. Or you can raise out the mixer and tilt the kettle with a hand crank to empty it. The mixer lifts vertically out of the hopper by a hydraulic pump. It is hydro approved and has Allen - Bradley variable speed drives and Seimens smartline touch screen controls. In very good working condition. Last used in a cosmetic facility.
This microfluidizer is all stainless steel. The heat exchanger is 500 psi shell, 150 psi tubes, 250°F temperature. It has a hydraulic fluid pump and reservoir, pressure control and gauge, prime / relief valve. Unit is on casters. Last used in a pharmaceutical facility. Specifications: Operating Pressure: 4,000 to 18,000 PSI, (270 to 1200 bar). Nominal flow rate: 0.5 to 0.6 GPM, (1.9 to 2.3 LPM). Sample size: 1 gallon to continuous.
This is a jacketed scrape surface kettle with emulsifier in the bottom and vacuum capabilities. The kettle is 29.5" diameter x 36.75" deep (250 litre capacity). The lid has 2 inlets, 2 spray ball inlets and 2 vacuum ports. There is a viewing port and a light inside that can come on to see inside when mixing. The mixer is single motion scrape surface and can run in forward and reverse. It can run 0 - 64 rpm. The homogenizer is in the bottom centre of the kettle and it can run 0 - 3600 rpm. It has a 3" outside diameter sani clamp connection. The mixer lifts vertically out of the hopper by a hydraulic pump. It is hydro approved and has Allen - Bradley variable speed drives and Seimens smartline touch screen controls. In very good working condition. Last used in a cosmetic facility.
316 stainless steel. The mixer is 36" wide x 30" long x 36" deep. Approximately 15 cubic foot working capacity. The lid lifts up and down with an air cylinder on the back. It has a 2.5" outside diameter sani clamp connection inlet and a 8.5" diameter inlet with a grate over it for adding product. The lid has safety lockouts and clamps to keep it closed. The mixer has a hand crank tilt for unloading. When fully tipped over it's 20" from the floor. In good working condition. Last used in a pharmaceutical facility. Comes with new packing glands.
Equipment type Mixer Manufacturer Hobart Quantity -1 Description Mixer Hobart Legacy Model HL 1400N 200-240 volts, 3 ph, 5 hp, 60 hz, 1200 rpm With 140 qt SS bowl, flat batter hobart 140 qt. SPECIFICATIONS Condition Date of manufacture Electric data 208 volts Located in Montreal Production capacity 140 qt Measures
Equipment type Mixer Manufacturer Hobart Quantity -1 Description Hobart Mixer Mélangeur Modèle L-800 Hobart Model L-800 80 Quart mixer including bowl and dolly with beater arm and hook attachments in stainless steel. Driven by 1.5 HP, single phase, 60 Hz, 230 volt, 8.5 AMPS motor. Serial number 11-466-235. SPECIFICATIONS Condition Date of manufacture Electric data 208 volts Production capacity 80 pints Measures
DCI 100liter Pressurized Vacuum Jacketed Reactor Tank With Agitator Stainless steel construction Electropolished internal finish Dished top and cone bottom Including Footpads load cells CIP inlets with spray ball Motor 208 volts 1.5amps 60hz 3ph 1725 rpm ½ hp Vessel MAWP 100 – 15 psi 302Fahrenheit Jacket MAWP 150 – 15 psi 365Fahrenheit Electric data Motor 208 volts 1.5amps 60hz 3ph 1725 rpm ½ hp