Northwood 5' x 12' CNC Router

Manufacturer Northwood
Model 5' x 12' CNC Router
Year 2012
Country USA USA
Condition Good
Main category Woodworking
Subcategory CNC Router
ID P90618042

This system was removed from service and packaged up by the technician. It is ready to ship.
5' x 12' Table
Includes: Schmalz Vacuum, Southworth Scissor Lift and Vacuum Pump
Hours of the machine: Power on time is 21,039 hours, Operating time is 5,908, cutting time is 3,095. Very low hours. The vacuum pump has 6,034 hours on it.
One (1) 18HP (13.5KW ), 4 Pole “Cartridge” Spindle with HSK F63 Chuck, programmable RPM up to 24,000, synthetic grease lubricated “Quad” ceramic bearings, a safety device for automatic fault detection, and a maximum tool shank diameter of 1".
One (1) Programmable Air Blast Nozzle at the spindle.
Spindle with Traveling Tool Changer Spindle Cartridge
TOOL CHANGER One (1) HSK F63 “Twelve Station” Automatic Tool Changer Carousel “Dynamic” carousel is attached to the spindle tooling plate (allowing back ground tool change while drilling) with a safety device for automatic fault detection. The maximum tool diameter capacity is 8″ per pocket with adjacent pockets empty and 4" with all pockets full. Total carousel weight capacity of 120 lbs One (1) Tool Changer Carousel Dust Shroud

VACUUM SYSTEMOne (1) 40 HP liquid ring vacuum system with a 10 micron inlet filter. The recirculation oil-vanetype pump supplies a maximum of 29.3 Hg vacuum (98% absolute vacuum) to two independentports on the worktables) at a maximum flow of 520 cfm.One (1) heavy duty exhaust/reclaim muffler-filter ensures quiet and clean operation.Vacuum Voltage: 460 volts, 3-Phase – 52 AMPS DRILLING UNITOne (1) dedicated 2.5 HP, 19-Spindle, L-Shaped Flexible Drilling Unit, with thirteen (13) verticalspindles (5 x 8) and three (3) double-ended horizontal spindles (2 x 4); 4000 RPM; 32mm pitch;independent selection Color LCD Touch Screen Monitor Control Pedestal with Remote MPG Fanuc CNC Control SystemPanel I FeaturesIntel Processor ‐ Windows 7 Operating System12.1" Color LCD ‐ Touch Screen Control PanelPanel I Memory 2GB RAM40 GB Hard Drive / DVD‐ROM Disk DriveNetwork Ready (Includes Card)CNC FeaturesOperationAutomatic operation (Memory)MDI Operation & DNC OperationSchedule functionProgram number searchSequence number comparison and stopWrong operation preventionBuffer register / Single blockJOG feedManual reference position return/shiftFull Function Manual handle feed (Remote MPG wheel)Feed FunctionRapid traverse/Feedrate overrideCutting federate clampAutomatic acceleration/declarationRapid traverse bell‐shaped acceleration/decelerationLinear acceleration/deceleration after cutting feed interpolationAutomatic corner deceleration (Look Ahead Control)Feedrate control with acceleration in circular interpolationAI advanced preview controlProgram InputTape codeOptional block skipExternal memory and sub program calling functionAbsolute/incremental programmingDiameter/radius programmingPlane selectionAutomatic coordinate system settingWorkpiece coordinate system/presetAddition of workpiece coordinate system pairDirect input of workpiece origin offset value measuredOptional chamfering/corner RProgrammable parameter inputSubprogram callCustom Macro BInterrupting type custom macroCanned cycles for drilling/ Small‐hole peck drilling cycleCircular interpolation by R programmingAutomatic corner overrideCoordinate system rotationProgrammable mirror imageFull Keyboard/Mouse Ports (Two (2) PS/2)One (1) Parallel PortFiber Optic Interface with CNC Controller (HSSB)Two (2) USB PortsTwo (2) Serial/RS232 PortsAxis ControlAxis Control by PMCAxis Synchronous/ Simultaneous ControlPosition SwitchInterpolation FunctionsNano interpolationPositioning/Single direction positioningExact stop modeCutting modeLinear, Circular, Cylindrical and Helical interpolationDwell (G4)High‐speed skipAuxiliary/Spindle Speed FunctionAuxiliary function2nd auxiliary functionSpindle analog outputSpindle OverrideDry RunTool function/Tool compensationTool offset memory (400 pairs)Tool radius/Tool length compensationTool length measurement & Cutter compensationInch/Metric compatibilityAccuracy compensation functionBacklash compensationStore pitch error compensationEditing OperationPart Program Storage Size (512K)400 Total Registered ProgramsPart program background and extended editingProgram protectSetting and DisplayCurrent position displayAlarm Message/Alarm History displayOperator Message/Operator History displayRun hour and parts count displayActual cutting federate displayMaintenance information screenOne (1) Button Work Surface Milling & Part Program OrientationOne (1) Dust Shroud Pushbutton Override for Safety

Manufacturer Northwood
Model 5' x 12' CNC Router
Year 2012

We add hundreds of new listings every week. Be sure not to miss any Northwood 5' x 12' CNC Router by subscribing to our email updates.

We also send announcements for upcoming auctions for Woodworking.

We hate spam as much as you do

None